Since the release of the Litter-Robot III Open Air, we have received many demands for a troubleshooting guide for this robot. ... My Litter-Robot III has stopped cycling on its own. I have reset it, turned it off and back on …If the above does not work: Unplug the unit for at least 5 minutes. (Disconnect backup battery if one is installed.) Completely close the Whisker app. After 5 minutes, plug the unit in and allow it to cycle until the blue “Ready” status lights up. Open the app and check for connection. Problem: Loading icon just keeps spinningMy litter robot 3 had the same problem: could not find the dump position and overturned when dumping. I called Litter Robot customer support. One told me to change the key and the other one told me to deep-clean or replace the globe. None of these worked. I ordered the wiring harness and replaced the old one. Now my litter robot 3 is working fine.Ensure proper placement. Your Litter-Robot comes fully assembled and ready to use. Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet.Litter-Robot 4: Purple light bar (Sleep mode) Litter-Robot is equipped with a sleep mode feature. When activated, this feature deactivates the cat sensors for a specified period of time, so the unit will not cycle automatically. Sleep mode is useful for units located in bedrooms or areas where you may not want Litter-Robot to cycle for a ...Litter-Robot 4: Light codes guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more.Once your cat is using Litter-Robot consistently, you can use it in Automatic Mode (leaving the unit on). 2. Stop scooping the old box. Place Litter-Robot near or next to the old litter box, but don't throw the old litter box away yet. Add a scoop of the old litter to the new litter in Litter-Robot to provide a familiar scent for your cat.the brand new litter will not complete an automatic cycle, red light stays on and setted at 3 min interval, but will complete a manual one either at the robot controls or the cellphone app, talked to technical support at whiskers and got forwarded to robotshop for technical help they think there is an hardware problem with the sensors, only one ...Now, let's run a test cycle. Short press the Reset button, then short press the Cycle button to run a clean cycle. Successful: After your Litter-Robot cycles, it should return to the Home position, displaying a solid blue light. If your waste drawer gauge is accurate (within 5%), you've been successful. Unsuccessful: If your waste drawer gauge ...The globe begins rotating counterclockwise with the solid yellow light on. After several seconds, press the 'Reset' button to pause the cycle. [/font] [font=system-ui, -apple-system, BlinkMacSystemFont, Segoe UI, Roboto, Oxygen-Sans, Ubuntu, Cantarell, Helvetica Neue, Arial, sans-serif] 7. While the cycle is paused, press 'Reset' again ...There are some litters that strictly do not work in the Litter-Robot such as: newspaper-based litters, non-clumping or loose-clumping litters, as well as absorbent wood pellet litters. ... Wait 15 seconds, then plug the Litter-Robot back in, and allow it to cycle until the blue "Ready" status lights up.It works seamlessly and the clumped litter drops into the bottom of the bin then the deodorizer starts working shortly afterwards. There were a few times where the robot got stuck because I accidentally added too much litter and the cylinder was too heavy to make a full rotation. So be careful not to add too much litter. 3. ZERO smell whatsoever.In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the...However, reducing the cycle delay may reduce the cleaning effectiveness if clumps do not have enough time to set, or clump. Extend the cycle delay when using a lower-quality clumping litter that needs more time to set. Settings. A 3-second long press of the Empty button enters or exits cycle delay setting mode.In the controls, you can power the Litter Robot off or on, lock the buttons if you have a cat that likes to bump them, turn on the night light, turn on sleep mode (it won't cycle for the 8 hours you tell it not to), and set your cycle delay (3, 7, or 15 minutes as I mentioned previously).With that in mind, we enlisted picky kitties — shoutout to Murphy, Frank, Romy, June, Beau, and Picasso — to test the most popular automatic litter boxes available today, including Whisker's Litter-Robot 4, Meowant's Self-Cleaning Cat Litter Box, and Amazon's favorite, the PetSafe ScoopFree Crystal Pro Self-Cleaning Cat Litter Box.Hi, The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking, let's start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2 ...Litter-Robot 3: Cat not detected ; Litter-Robot 3: Cat Sensor Troubleshooting Litter-Robot 3: Control Panel Lockout Litter-Robot 3: Cycle delay setting ; Litter-Robot 3: Deep Cleaning Litter-Robot 3: Filling the Globe ; Litter-Robot 3: Fixing a Loose GearIf the solid red light does not resolve itself after a clean cycle, watch this video or try these tips: Placement: Ensure the unit is on a solid floor/surface (no carpet). Any litter mat should be in front of the unit, not underneath. Back of the robot should not be touching any walls or other surfaces. Troubleshooting:While the Litter-Robot 4 is generally low-maintenance—especially when compared to traditional litter boxes—about six months into use, one day the globe began to stop mid-cycle.May 14, 2022 ... ... Cycling 3:38 Cleaning Performance 4:14 Using ... Short story: it's absolutely fantastic, do not hesitate. ... Litter Robot 4 vs Litter Robot 3 ...the brand new litter will not complete an automatic cycle, red light stays on and setted at 3 min interval, but will complete a manual one either at the robot controls or the cellphone app, talked to technical support at whiskers and got forwarded to robotshop for technical help they think there is an hardware problem with the sensors, only one ...Litter-Robot 4. Since the firmware update (at least I think the last update), every time my litter robot 4 cycles, it gets to about halfway (dumping the waste in the bin) and then it gets stuck. The wifi and empty bin buttons turn yellow (so I have 3 blue 2 yellow) and the app sends a message that says "Scale active for too long".Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Chat with us 1.877.250.7729 Submit a ticket. Explore the newest features and improvements in our latest firmware update for Litter-Robot. Keep your unit current and operating at its best with our comprehensive firmware updates.If the bonnet is not seated properly, this will cause the unit to start and stop during a cycle or not cycle at all. Another option could be that the black key on the back of the globe is not in the slot and it is lifting the bonnet. To make sure your bonnet is seated properly, please follow these instructions: Disconnect the bonnet.Tasmanian devils are typically born in litters of two or three after a gestation of 21 days and continue development in the mother’s pouch while nursing for an additional four mont...Litter-Robot by using some catnip or a favourite treat. 2. Add a scoop of litter from the old litter box to provide a familiar scent for your cat. 3. Place treats on the step or handle around the Litter-Robot so your cat associates rewards with the unit. 4. Once you notice that your cats have used the Litter-Robot, power the unit on to cycle ...The Litter-Robot houses a hall effect sensor inside the base and magnets inside the globe. When the magnet in the globe reaches the sensor, the globe stops. It is possible that there is an issue with the sensor in this case. Unless you see anything wrong with the rubber inside the globe. There could also be an issue with the circuit board.The Litter-Robot 3: 7,880 reviews with 4.6/5 stars ; The Litter-Robot 3 Connect: 8,415 reviews with 4.5/5 stars ; The Litter-Robot 2: 1,255 reviews with 4.5/5 stars ; It's convenient, effective, and time-saving: that's at least the consensus when it comes to the Litter-Robot. Others found it easy to use, and it proved beneficial in masking ...Litter-Robot 4 Bundle by Whisker, White - Automatic, Self-Cleaning Cat Litter Box, Includes Litter-Robot 4, 6 OdorTrap Pack Refills, 50 Waste Drawer Liners, Ramp, Mat & Fence 4.2 out of 5 stars 198If you want to do a hard reset on your Litter Robot 4 you must do the following: Press and hold the Reset and Wifi buttons for three seconds. The panel's light will start a sequence of red, blue, and green, and a cleaning cycle will start. When the cleaning cycle is completed the hard reset was done successfully.Rapid cycling bipolar disorder mood shifts can occur more quickly than symptoms of bipolar disorder I or II. Rapid cycling may be a temporary experience for someone with bipolar di...Sep 12, 2016 ... ... cycling when your kitty is inside of the litter box). ... It does not cost you anything extra to use them. ... How to Clean the Litter-Robot 3 ...Unfortunately, black cat emoji are not so prevalent. In 2012, Android 4.3 comprised a release of black and white emoji, which included a set of black cat emoji by default. However, there's some hopeful news on the horizon for black cat emoji: Emojipedia lists Black Cat as new in Emoji 13.0, coming to more platforms in the second half of 2020 ...1. When your cat exits the Litter-Robot, a timer counts down, allowing the litter to clump before the clean cycle begins. 2. During the clean cycle, the globe slowly rotates. The patented sifting process separates the clumps from the clean litter. 3. The clumps are deposited into a fully enclosed waste drawer located below the globe with a ...Here's what I told Litter Robot, " Every time it's used, it half cycles and I have to power it off and power it back on for it to cycle. Pushing the "cycle" ...Probably the closest competitor to the Litter-Robot is Leo's Loo Too litter box (8/10, ... When it does start a cleaning cycle, it is nearly silent. Most of the time, I don't even notice it ...Preparation. Litter-Robot 4 continuously monitors the motor current to ensure the globe is rotating smoothly and is not obstructed. If your unit has a red light bar with partial yellow flashing, this indicates that the globe is most likely jammed or overloaded. The unit will retract and try to continue cycling.Litter-Robot 3: Cycle delay setting. The cycle delay is the elapsed time starting from when your cat exits the globe until the unit starts a clean cycle. It can be set for 3, 7, or 15 minutes. The default cycle delay is 7 minutes. Reduce the cycle delay if it is important to minimize odor and/or the time that waste is accessible to other pets ...Litter-Robot 4. Since the firmware update (at least I think the last update), every time my litter robot 4 cycles, it gets to about halfway (dumping the waste in the bin) and then it gets stuck. The wifi and empty bin buttons turn yellow (so I have 3 blue 2 yellow) and the app sends a message that says "Scale active for too long".Related: "Dump Position Fault" fixing in Litter-Robot. Tips to Keep Your Litter-Robot Working Like New. Below are some of the steps you can take to keep your Litter-Robot working—and hopefully, smelling—like new. Doing so also prevents several issues, such as the machine getting stuck mid-cycle. As they say, prevention is better than ...During an Empty cycle, press the Cycle, Reset, Empty, or Connect button to pause the cycle. Press the Cycle button to resume the cycle. Press the Cycle button to resume the cycle. Press the Reset button to abort the cycle and return the globe to the Home position.Cat detection. The Litter Robot 4's sensors detect the weight change when your cat both stands on the step and gets completely into the machine, and runs a clean cycle after they leave. It also ...Combined with Litter-Robot's prompt cleaning cycle and fully enclosed, carbon-filtered waste drawer, litter box smells are a thing of the past. For best results, replace the pack every two weeks. ... (The pod is not necessary for Litter-Robot 4.) For a natural solution to pet odor elimination, try our premium cat litter and OdorTrap™ Packs ...Your Litter-Robot 4 cat sensor has been activated. This means that your cat has recently entered the globe, and the wait time countdown to the clean cycle has been initiated. No action is needed. If the solid red light does not resolve itself after a clean cycle, watch this video or try these tips: Placement:Sep 17, 2021 ... Problems: flashing blue 'ready' light flashing yellow 'cycle' light solution: complete deep clean by disassembling unit most importantly: ...Ok so on the side of the bonnet there are 2 tabs make sure they are clicked in. Maybe try taking it off and then placing it back on. You should be able to press the in with your fingers. Shouldn't need any tools. I have never heard of a "keyhole plug".In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the...To unpause the unit, press the cycle button. To abort the clean cycle, press reset or empty. Press any button to put the unit on pause. On the other hand, a blinking yellow light signals a problem. The flashing sequence determines how to resolve the issue.Nov 30, 2016 ... ... not completing Tools needed: - A Phillips ... Litter-Robot 3 base in our Litter-Robot 3 disassembly guide here: ... What To Do When Litter-Robot ...Aside from the main power light, there are three lights on the Litter Robot 3 control panel, which are blue (ready button), yellow (cycling button) and red (timing button). There are also four buttons which are "power", "cycle", "empty" and "reset".Shop LItter-Robot 4. Meet Litter-Robot 4, the next evolution of the highest-rated WiFi-enabled, automatic, self-cleaning litter box for cats.No, the Litter-Robot does not have a weight limit. With entryway dimensions of 16"H x 10.25"W and interior globe dimensions of 15"-17"H (depending on litter level) x 20"W x 20"D, almost any domestic cat can fit comfortably inside the globe. ... estimating the total number of scoops you've avoided. The count may vary with the occasional cycle ...If you’re in the market for a new robotic vacuum, look no further than iRobot Roomba. With its advanced technology and efficient cleaning capabilities, the Roomba has become a hous...Is your $700 cat box a pile of crap? In more ways than it should be? I think that I finally found a fix for mine! Stay tuned!Litter-Robot 3: Yellow and red or blue and red flashing (Motor over torque) If Litter-Robot 3 globe becomes jammed or overloaded when rotating clockwise, the motor will stop and reverse for 5 seconds. The unit will start to cycle again after 15 seconds, to attempt to return to the Home position. If after three attempts, the unit is unable to ...Litter robot 4 not cycling back to the right- my litter robot 4 will cycle left like it is going to empty litter but when it tries to go back it gets stuck in the same spot. Is anyone having this issue? I have tried everything even taking off the globe to re-set, un plugged, emptied- nothing helps! Litter-Robot 4If the CATS does not engage, refer to step 5. If your CATS does not engage, leave the unit off & unplugged. Notify us so we can make the necessary arrangements based on warranty. The surface for your Litter-Robot should be hard to avoid the unit taking on extra absorption of weight.Empty button = empty all the litter out of the globe so I can clean it. These two buttons are not the same. Pressing the cycle button spins the globe to the left (counterclockwise) so that the clean litter goes in the screened pocket (called a septum) and any clumps end up in the waste drawer. Pressing the empty button rotates the globe to the ...The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...Submit support request. Select a category for your ticket. Select a sub-category for your ticket. Please describe your issue. Got questions or issues? Contact Litter-Robot Support today. We're dedicated to ensuring a seamless experience for you & your pet.Hi! Try increasing/decreasing the wait time setting to accommodate your litter. Clumps usually stick if they are too wet when the Litter-Robot cycles. If that doesn't do the trick, you might consider trying a different type/brand of litter. My kitties go at the edge of the litter also.My litter robot stops upside down during cycling. I have owned my Litter Robot 3 for a little over a year and about a week ago it began to get stuck upside down when cycling. The litter box becomes unusable, and the wastebin is exposed. The yellow light is blinking. In order to fix it, I've been having to turn the unit off and back on.Press the Cycle button to resume the cycle. Press the Reset button to abort the cycle and return the globe to the Home position. 3. After the litter is emptied, the globe pauses with the yellow light bar on and awaits your action. You may need to sweep any remaining litter toward the waste port. 4.Vacuum the inside perimeter of the bezel with a brush attachment, passing over the holes at the top of the bezel where the curtain sensors are located. Now, let's run a test cycle. Short press the Reset button, then short press the Cycle button to run a Clean cycle. After Litter-Robot cycles, it should return to the Home position, displaying a ...Mar 7, 2019 ... a Litter-Robot? Natural Clumping Cat Litter 2:43 What does "cycle" mean on the Litter Robot 3? And this part shows "What does litter robot do .....Our litter robot stopped working mid-cycle yesterday. The yellow light has remained on (not flashing) and it does not respond to any activity anymore. We have taken apart all the pieces and made sure they are clean. We unplugged it for a few hours but as soon as it’s turned on again, the yellow light reappears.The Litter-Robot will automatically perform a clean cycle (which takes about 2 ½ minutes). Afterward, turn it off/unplug it again. Continue this supervised, semi-automatic mode until your kittens have gained sufficient weight to activate the cat sensor. ... No, the Litter-Robot does not have a weight limit. With entryway dimensions of 39.4 cm ...WhiskerCare™ Warranty disclaimer. Litter-Robot is the highest-rated automatic, self-cleaning litter box for cats. 90-day in-home trial. 1-year warranty. Free shipping*. Designed & assembled in the USA.Litter-Robot 4: Purple light bar (Sleep mode) Litter-Robot is equipped with a sleep mode feature. When activated, this feature deactivates the cat sensors for a specified period of time, so the unit will not cycle automatically. Sleep mode is useful for units located in bedrooms or areas where you may not want Litter-Robot to cycle for a ...Robots and artificial intelligence (AI) are getting faster and smarter than ever before. Even better, they make everyday life easier for humans. Machines have already taken over ma...Make sure waste bin is empty -> push reset button -> push cycle button. Unplug from power -> check waste port in globe for clumps / obstructions -> Plug in & power on -> complete two manual cycles. Litter-Robot 4 Solid Red [Cat Detected] Wait for set wait timer to complete after last cat detection (could just be normal cycle) Can hit the reset ...Jan 22, 2023 · Related: “Dump Position Fault” fixing in Litter-Robot. Tips to Keep Your Litter-Robot Working Like New. Below are some of the steps you can take to keep your Litter-Robot working—and hopefully, smelling—like new. Doing so also prevents several issues, such as the machine getting stuck mid-cycle. As they say, prevention is better than ...When the light sensor, located in the control panel, detects low-light conditions, the night light turns on automatically. The automatic night light, located in the upper bonnet, is there to help guide your cat to the litter box. A light sensor located above the Cycle button detects ambient light and turns the night light on and off automatically.That is not the function of the reset button. It does NOT reset the gauge in the LR4 or the LR3. "Press the Reset button while the Globe is at the Home position with the blue Light Bar on to reset the Cat Sensor(s). When pressed during a cycle, it will pause the cycle. If pressed again while paused, it will abort the cycle.Delete the robot from the app altogether. Turn off the robot and unplug the power cord from the base. Then log out of the app and close it as before. Plug in the robot and turn it on. Let it do its initialization cycle. Restart the app and login. Do the onboarding as if you were installing a brand new robot.Ensure proper placement. Your Litter-Robot comes fully assembled and ready to use. Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet.Litter-Robot 3: Control Panel Lockout Litter-Robot 3: Cycle delay setting ; Litter-Robot 3: Deep Cleaning Litter-Robot 3: Filling the Globe ; Litter-Robot 3: Fixing a Loose Gear Litter-Robot 3: Fixing the globe magnets ; Litter-Robot 3: Night Light Feature